Interlink-electronics DuraPoint Manual de usuario Pagina 1

Some integrators may want to completely seal the DOM into a system.By following the instructions below, a NEMA 4X/IP66 seal can easily be obtained.RTV

RS232C Serial-Interface Connections* See Figure 7.13 for details on the PS/2 pin-out convention** See Figure 7.08 for details on connecting the

3.3 Cabling OptionsDuraPoint OEM Interface CablesHeader/Mating Connector SpecificationsBelow is a list of Interlink Electronics' line of DOM inte

3.4 Cursor Speed OptionsDuraPoint provides three speed ranges: fast, medium, slow. Slow is the default.In this illustration Jumper 5 (JP5) is bridged

4.0 CUSTOM DESIGNSCustom DuraPoint OEM Module SolutionsInterlink Electronics specializes in customizing DuraPoint OEM pointing solutionsto meet your

6.0 SPECIFICATIONSRS232C serial and PS/2 mouse portMicrosoft serial and PS/2 two-button mouseWindows via serial and PS/2 ports.PS/2 compatible with an

Figure 7.01DOM Without Faceplate (Core Module)DuraPoint Integration GuidePage 12PRESSURESENSORFLEX-CIRCUITSHIELD LAYERFLEX-CIRCUIT(CONDUCTIVELAYER NEA

Figure 7.02DOM With Female FaceplateDuraPoint Integration GuidePage 133.054X 0.252X 2.80CLEARANCEBETWEENFACEPLATEAND KEYPAD3X 0.051.450.002X 1.200

Figure 7.03DOM With Male FaceplateDuraPoint Integration GuidePage 14CLEARANCEBETWEENFACEPLATEAND KEYPAD3 X 2.7503X 0.053 X 2.7503.1256 X6-32 X 0.500”S

Figure 7.04DOM, Side View and BOMDuraPoint Integration GuidePage 150.630.83APPROXIMATELOCATION OFPCB COMPONENTSMALE ORFEMALEFACEPLATEGASKET (MALEFACEP

CAUTION!Use caution when installingthe Module Sensor Tail.The Sensor Tail is susceptibleto damage if exposed tosharp edges.

Figure 7.05Suggested Mounting Without FaceplateDuraPoint Integration GuidePage 164X FASTENER LOCATIONSTO FIT 0.25 MOUINTINGHOLES LOCATED ONCORE MOD

Figure 7.06Suggested Mounting With Female FaceplateDuraPoint Integration GuidePage 17(2.44)(4.00)0.000.002X1.200.551.891.702X 2.002X 2.001.702X2.804X

Figure 7.07Suggested Mounting With Male FaceplateDuraPoint Integration GuidePage 18

Figure 7.08Circuit Board DetailDuraPoint Integration GuidePage 19(COMPONENTS NEAR SIDE)J3J11J2

Figure 7.09 “VP” Cable DetailsP7V 7 0PV 730VP710VP720-MINI DIN 8FEMALENN OCOECTR DIN-8MINIMALECONNOECTR SDB-9 ERIALLFEMAECONNECTORSHIELDLUGDB-9 S LERI

Figure 7.10Interfacing to the VP710 CableDuraPoint Integration GuidePage 21J3J21

Figure 7.11Interfacing to the VP720, VP740 and VP770 CablesVP720 ORVP740 CABLE4-PIN HOUSINGKEYING ARROWLOCATED AT REDWIRE FACES UPCONNECT CABLE SHIELD

Figure 7.12DB-9 and P/S2 Connector DetailsDuraPoint Integration GuidePage 23DATAGROUND+5VccCLOCKNO CONNECTIONNO CONNECTION

Figure 7.13COM Port Output FormatDuraPoint Integration GuidePage 24

THE SPEED SETTING ARE AS FOLLOWS: JP3 - FAST JP4 - MEDUIM JP5 - SLOW (DEFAULT)Figure 7.14PCB Assembly, Zilog Ma

Table of Contents ©1997, 2012 Interlink Electronics, Inc.Publication Number: 94-20994 Rev. BDuraPoint and VersaPoint are registered trademarks of Inte

8.0 WARRANTY INFORMATIONInterlink Electronics warrants the DOM against defects in materials orworkmanship for a period of one (1) year after date of p

9.0 PRODUCT SUPPORTThe DOM has been designed for quick and easy integration. However, if youhave any questions about integrating or using your DOM, p

Notes:

Do not print this information:This page is to be blank

546 Flynn Road • Camarillo, CA 93012 (805) 484-8855 • Fax (805) 484-9457 http://www.interlinkelectronics.com

DO NOT PRINT THIS PAGEDO NOT PRINT THIS PAGEThis page is for document control purposes &to provide printing instructions only.These instructions a

Do not print this information:This page is to be blank

SpecialNote:Thank you for purchasing the DuraPoint OEM Module (DOM), the durablepointing device designed to operate in harsh environments. The module

2.0 Operating the DuraPoint OEM ModuleDuraPoint Integration GuidePage 2DuraPoint is designed to be easy and intuitive to use. The mouse buttoncontrol

2.2 Clicking and DraggingDuraPoint Integration GuidePage 3The click buttons, located on either side of the mouse button, incorporatepressure-sensitiv

DuraPoint Integration GuidePage 43.0 INTEGRATION NOTESSpecialNote:3.1 Mounting and Sealing the DuraPoint OEM Module The DOM is designed to be blind m

DuraPoint Integration GuidePage 5DURAPOINTOEM MODULEPANEL FACEMounting the DuraPoint OEM Module To panel mount the DOM without sealing, all that is ne